DoorKing 1812 El manual del propietario descargar pdf

120 Glasgow Avenue

Inglewood, California 90301

U.S.A.

CENTRAL

OFFICE

EARTH

GND

PHONE

OUT

HOME

2345678

SW1

ENTRY BY-PASS

1875-010

CENTRAL

OFFICE

EARTH

GND

PHONE

OUT

HOME

2345678

SW1

ENTRY BY-PASS

1875-010

It is highly recommended that you consult the Installation/Owner’s manual for complete instructions on all the different types of installations. The 1812 Access Plus

Telephone Entry System involves the installation of the 1812 cabinet, the by-pass board for the incoming telephone line, and wiring of these components (On reverse side).

Be sure that all dirt, metal or wood debris is removed from inside cabinet after mounting it. This could damage the control board and cause a malfunction during operation.

Remove Control Board from Cabinet

Flush Mount Cabinet in a Pilaster, Wall or Kiosk

The control board removal is the same for all models.

1. Unlock and open the 1812 Access Plus door.

2. Disconnect the keypad plug and door accessories

plug from the control board.

3. Remove the 4 screws. Carefully remove control board.

CAUTION Keep the control board in a protected area

during the installation.

SPE

VOL

1970-010

MOD

1972-010

BAD

OWN

RS-

485

RJ-45

Jack

(Cat5)

Use existing 4 holes in cabinet box to bolt the surface or wall mount models on a DoorKing

mounting post (there are several different styles available). Use the hardware that is supplied with

the mounting post. Run all necessary wires through the post to the cabinet (See reverse side).

Mount Cabinet on a Mounting Post

Use the 4 existing holes in the cabinet box to screw the surface or wall mount models to

the wall. Run conduit inside or outside of wall or pilaster if desired. Use appropriate

hardware to mount the cabinet (Not supplied). Be sure that the mounting hardware does

not protrude into the cabinet where it could cause a short. Run all necessary wires through

the conduit to the cabinet (See reverse side).

Mount Cabinet Directly to a Wall or Pilaster

Install the By-Pass Board

The 1812 Access Plus by-pass board provides a method to by-pass the 1812 Access Plus and route the

incoming telephone line directly to the homeowner’s phone. It must be installed as part of the 1812

Access Plus system. All telephone wires for the 1812 Access Plus must pass through the by-pass board.

Mount the by-pass board in a location that is easily accessible by the homeowner. In case of 1812 Access

Plus trouble or maintenance, the homeowner will use the by-pass switch on the board to route the

incoming telephone line directly to their home phone. If the by-pass board is installed outdoors, it must be

installed in a NEMA Type 4 enclosure (not supplied) with conduit to protect the board and wires from

direct exposure to landscape sprinklers, rain, snow, and other elements.

NEMA Type 4

enclosure for

outdoor

installation.

(Not Supplied)

Use only twisted pair telephone wire that is rated for direct

underground burial (Cat5e Gel Filled (flooded) UV resistant

direct burial cable in conduit is recommended).

DO NOT use wire that is rated for indoor application use.

DO NOT run telephone wires in the same conduit as high

voltage AC wire.

It is recommended to run all necessary wires to the by-pass

board (See reverse side) in a “dedicated” telephone wire

conduit.

Ground by-pass board.

Minimum 12 AWG wire

(Not supplied).

If installed

outdoors.

Plastic screw anchors for

masonry if required.

(Not supplied)

Dedicated

Telephone

Wire Conduit

“Entry” switch position:

Routes incoming phone line through 1812

Access Plus and then to the home phone.

7 8 9

4 5 6

“By-Pass” switch position:

Routes incoming phone line directly to the

home phone, bypassing 1812 Access Plus.

7 8 9

4 5 6

From

Incoming

Telephone

Line

From

1812’s

18-Pin

Main

Terminal

Surface

Mount

Cabinet

Wall

Mount

Cabinet

Flush

Mount

Cabinet

Surface

Mount Curved

Cabinet

8 9

4 5 6

1 2 3

4 5

1 2

8 9

5 6

2 3

Mount rough-in box into the pilaster, wall or kiosk. Run conduit inside wall into bottom of rough-in

box if desired. Use appropriate hardware (Not supplied) to secure the rough-in box in place. Run all

necessary wires through the conduit in to the rough-in box (See reverse side).

Bolt flush mount box

into the rough-in box

with 4 supplied bolts.

ough-In Box

SPEAKER

VOL

MIC VOL

KEYPAD

CODE

1970-010

123

8910

MODEM

72-010

SW1

BAD

DNS

LAN

DOWN

RS-485

RJ-45

Jack

(Cat5)

Flush

Mount

Box

4 5

Conduit

(Shown inside wall)

Conduit

(Shown inside wa

ll)

8-Pin

RS-485

Connector

18-Pin Main

Terminal

Connector

Remove the 18-pin main terminal

connector, and if necessary, the 8-pin

RS-485 connector from the control

board by gently pulling them straight

up. This will make wiring to the

control board easier. Note the

orientation and numbering sequence

of each connector to correctly wire it.

IMPORTANT The 1812 Access Plus and by-pass board

MUST be properly grounded! A gooseneck mounting post

anchored in concrete does not make a good ground.

CENTRAL

FFICE

EARTH

PHONE

OUT

HOME

2345

SW1

ENTRY BY-PASS

1875-010

From

Home

Phone

Incoming

Phone Line

Home Phone

Incoming

Phone Line

Home Phone

QUICKSTART “BASIC” INSTALLATION GUIDELINES FOR AN 1812 ACCESS PLUS CABINET AND BY-PASS BOARD

1 2

Indice de contenidos

Pagina 1 - Install the By-Pass Board

120 Glasgow AvenueInglewood, California 90301U.S.A.1CENTRALOFFICEEARTHGNDPHONEINPHONEOUTHOME2345678SW1ENTRY BY-PASS1875-0101CENTRALOFFICEEARTHGNDPHONE

Pagina 2 - Control Board

120 Glasgow AvenueInglewood, California 90301U.S.A.KEYPADMASTERCODE1970-0101112345678910J2J1J3181716 Com15 N.C.14 N.O.13 Com12 N.C.11 N.O.1098765 RING