DoorKing 1812 El manual del propietario

Owner’s Manual Model 1812 Telephone Intercom Systems P/N 1812-065 REV H, 7/01 Copyright 2001 DoorKing, Inc. All rights reserved. DoorKing, In

10 Surface mount units can be mounted directly to a wall or pilaster or post mounted using a DoorKing mounting post (p/n 1200-045 or 1200-046). Be

11 Surface Mount Dimensions 1#0*7 8 96543210.0 5.252.8756.1253.05.02.52.5.8751.251.31.875 Dia

12 Flush mount units are not designed for direct exposure to the weather. Be sure the unit is mounted securely and is not subject to vibration fro

13 1812-150 Rough-in Box Dimensions Flush Mount Dimensions1#0*7 8 96543211.07.253.06.1254.253.05.09.0 O/C5.25 O/C.8752.01.7510.0.875 Dia 10.757.03.

14 • The by-pass switch should be installed in a location where it is accessible by the homeowner. • The by-pass switch must be protected from the

15 If any alarm systems are installed on the phone line, be sure that the alarm interface precedes the 1812 by-pass switch interface. 1. Connect P

16 If any alarm systems are installed on the phone line, be sure that the alarm interface precedes the 1812 by-pass switch interface. Use this wir

17 Use this wiring diagram when a single 1812 is programmed for intercom mode and is connected directly to another telephone or to an un-used C.O.

18 Use this wire diagram when multiple 1812 units will be connected together in an intercom mode and connected directly to another telephone or to

19 • External time clock input may be used to create an additional time zone for entry codes. • Two 12 volt, .8 amp gel-cell batteries (DoorKing

2

20 • If the 1812 is to be powered from a 24-Volt DC source such as batteries or solar panels, it is recommended that the panel light be removed.

21 SECTION 2 – PROGRAMMING The DoorKing 1812 Telephone Intercom System can be programmed by three different programming methods. • KEYPAD: The key

22 Prior to programming the 1812 with the DoorKing Auto-Programming Software for Windows, the system must have the MASTER CODE and SYSTEM SET-UP in

23 Proceed with the programming steps on the following pages if PC programming will not be used. 2.3.1 Relay Strike Time These steps will progr

24 2.3.3 Phone / Intercom Mode The 1812 is normally connected in series with a residents incoming phone line, which supplies a constant source of D

25 2.3.6 Number of Rings This programming section sets the number of rings that the 1812 will allow to pass through the system before it picks up t

26 2.4.1 Time Clock Programming This programming sequence programs the calendar chip in the 1812 system for the current time and date. The calenda

27 2.4.3 Automatic Relay Activation Time Zones This program sequence sets up time zones to automatically activate and deactivate the relays on the

28 2.4.5 Call Forward Time Zone This programming sequence sets up a time zone for the call-forwarding feature. The 1812 will automatically send cal

29 2.5.1 Call Forward Programming These steps program the call forwarding telephone number into the 1812 memory. Call forwarding can only be used

3 Use this manual with the following models only. All 1812 Telephone Intercom Systems with circuit board 1871-010 REV S or higher. DoorKing, Inc.

30 2.6.1 Four-Digit Entry Code Programming This programming sequence programs four digit entry codes into the system memory. You can store up to 5

31 SECTION 3 – ADJUSTMENTS Speaker Volume The speaker volume potentiometer is labeled SPEAKER VOL on the control board. The speaker volume should b

32 Circuit Board Adjustment Locations PH InPH OutMstrCodeKeypadSpkr Vol123456789101112131415161718FB 1FB 21 2 3 4 5 6 7 8

33 SECTION 4 – OPERATING INSTRUCTIONS 4.1 Calling the Resident To place a call from the 1812 to the resident’s house, the guest simply presses the

34 4.3 Preprogrammed Numbers To use the preprogrammed phone number feature, the guest simply presses 01, 02, or 03 on the system keypad. The 1812 wi

35 Resident Operating Instructions The following operating instructions assume that the 1812 features are being turned on and off from the resident’

36 4.8 Entry Code Time Zone Enable / Disable The entry code time zone affects only those entry codes programmed under the time zoned entry code loc

37 4.11 Relay Activation Check The 1812 can be called to check if relay 1, relay 2, or both relays in the system are latched and holding a door or

38 4.14 Switch Input Operation A switch closure between terminals 7 and 9 will activate relay 1 for its programmed strike time. A switch closure be

39 SECTION 5 – MAINTENANCE The DoorKing telephone entry system is essentially a maintenance free device. When the unit is properly installed, it s

4 Preface Important Notices...

40 Isolating Noise Problems 1. Remove all external items connected to the 1812 unit, such as back-up batteries, relay connections, push button swit

41 SYMPTON POSSIBLE SOLUTION(S) Cannot get into programming mode. • Wrong master code entered. Start over. • Waiting too long between pushing butt

42 SYMPTON POSSIBLE SOLUTION(S) System generates tone when granting access to a visitor, but will not work on regular phone line. • Switch the wi

43 Slave Keypad Allows remote activation of the system relays by use of the entry codes. Does not provide any voice communication to the main un

44 Complete the information in the tables on the following pages to maintain a record of the information that has been programmed into the telephon

45 Entry Code Log Sheet Location Number Relay Function Entry Code Location Number Relay Function Entry Code 01 1 Momentary 26 2 Momentary 02

5 Section 3 – Adjustments Speaker Volume...

6 FCC - UNITED STATES This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the F

7 • Prior to beginning the installation of the telephone entry system, we suggest that you become familiar with the instructions, illustrations, an

8 • Unique telephone communication system allows homeowners to use their telephone as an intercom to speak to a guest at a front door or gate, and

9 SECTION 1 - INSTALLATION • Installation of the telephone intercom system involves the installation and wiring of the Entry System By-pass Switch