DoorKing 1812 El manual del propietario

Model 1812 Plus Residential Telephone Intercom / Access Control System Owner’s Manual DoorKing, Inc.120 Glasgow AvenueInglewood, California 903

1.2 Mount the By-Pass Switch The 1812’s by-pass switch provides a method to remove the 1812 from the telephone line and reconnect the homeowner’s tel

1.3 Dimensions Surface Mount 1#0*7 8 96543210.0 5.252.8756.1253.05.02.52.5.8751.251.31.875 Dia Surface Mount Curved 11.0 6.256.753.3755.52.52.51#0

Flush Mount Rough-in Box 10.257.54.53.55.0 2.6251.25 Dia Flush Mount 1 2 3654987#0*9.2512.04.253.5.875 Dia7.256.2510.02.55.0Page 12 1812-161-E-1-1

Wall Mount 10.75 3.57.3751 2 3654987#0*2.52.51.1251812-161-E-1-10 Page 13

1.4 Telephone Line Wiring Be sure to observe electrical safety when working with phone lines. Phone lines carry electricity and the ring voltage can

TELEPHONE LINE WIRING WIRE SIZE MAX DISTANCE IN FEET 24 AWG 800 22 AWG 1600 20 AWG 2200 18 AWG 3600 1.5 Power Wiring Do not run telephone lines

1.7 Wiring for a Single Unit – Telephone Mode DOORKING1875-010GNDENTRY BY-PASS12345678C.O. PH IN PH OUT HOME16.5 VAC20 VAMag LockPowerDOORKING, INC.

1.8 Wiring for Multiple Units – Telephone Mode DOORKING1875-010GNDENTRY BY-PASS12345678C.O. PH IN PH OUT HOMEDOORKING, INC., INGLEWOOD, CA 90301Da

1.9 Wiring for Single Unit – Intercom Mode DOORKING, INC., INGLEWOOD, CA 90301Date: Dwg. No. Rev.Title:2/09AM1812P-0031812 Plus – single system.Ba

1.10 Wiring for Multiple Units – Intercom Mode DOORKING, INC., INGLEWOOD, CA 90301Date: Dwg. No. Rev.Title:2/09AM1812P-0041812 Plus – multiple sys

Page 2 1812-161-E-1-10

1.11 Main Terminal Description Terminal Description 1 Phone In (Negative) 2 Phone In (Positive) 3 Ground 4 Phone Out (Positive) 5 Phone Out (Ne

SECTION 2 – PROGRAMMING Before You Start The 1812 has been programmed at the factory with many of the programming parameters already set (default set

Programming Guide TableSystem Parameters Section 2.2 Description Command Section Default Value Phone / Intercom Mode * 0 6 2.2.1 Phone Single / Mul

IMPORTANT! We strongly suggest that you read these programming instructions in their entirety before beginning any programming of this telephone entr

2.2 System Parameter Programming 2.2.1 Phone / Intercom Mode Default setting is 1 (Phone Mode). The 1812 is normally connected in series with a resi

2.2.5 Number of Rings to Ring Residence Default setting is 05 (5 Rings). When the CALL button on the 1812 is pushed, this programming sequence sets t

2.2.8 Tone Open Numbers Default setting for Relay 1 is 9876. Default setting for Relay 2 is 5432. These steps will program the tone open number(s) f

2.2.10 Hang Up Tone Default setting is 0. These steps set the number that will hang-up the 1812 after the conversation is completed. The hang up ton

2.2.13 Set Call Forwarding Microphone Gain and Speaker Volume Default setting is 71. This adjustment is required only if call forwarding in the 1812

2.3 Directory Codes 2.3.1 Directory Codes 24 – 50 Dial Phone Number The 1812 has the capability of operating as an auto-dialer system and can store

Use this manual with the following models only. 1812-Plus Residential Telephone Intercom / Access Control System with circuit board 1971-010. DoorKi

2.4 Devices 2.4.1 Simple Access Code Programming This programming sequence programs simple access codes into the system memory. Simple access codes

2.4.4 Delete All Access Codes This programming sequence deletes all access codes. WARNING: Once started, all access codes will be erased. 1. Pres

2.5 Time Functions 2.5.1 Program Calendar Chip This programming sequence programs the calendar chip in the 1812 system for the current time and date

2.5.3 Call Forward Phone Number Programming These steps program the call forwarding telephone number into the 1812 memory. Call forwarding can only b

2.5.5 Relay Hold Schedule Default setting in step 3 is 0 (Hold schedules are OFF). This program sequence sets up schedules to automatically activate

2.5.6 Time Zones Default setting in step 3 is 0 (Time Zones are OFF). This programming sequence sets up time zones (up to 4) that can be applied to th

2.6 Miscellaneous 2.6.1 Restore Defaults This step will restore the factory set defaults for each of the programming parameters. WARNING: Once star

SECTION 3 – ADJUSTMENTS Speaker Volume The speaker volume potentiometer is labeled SPEAKER VOL on the control board. The speaker volume should be adj

Page 38 1812-161-E-1-10

SECTION 4 – USER INSTRUCTIONS 4.1 Resident Operating Instructions 4.1.1 Granting or Denying a Guest Access To place a call from the 1812 to the res

Table of Contents Preface Important Notices...

4.1.3 Dial-Out Phone Numbers To use the dial-out phone number feature, the guest simply presses a two-digit directory code (24-50) on the system keyp

4.2 Remote Operation 4.2.1 Remote Programming The 1812 can be programmed and operated from a remote location using a touch-tone telephone. Be sure th

4.2.3 Relay Activation The 1812 system relays can be activated from the house. Refer to the tone open numbers that where programmed in section 2.2.8

SECTION 5 – MAINTENANCE The DoorKing 1812 telephone entry system is essentially a maintenance free device. When the unit is properly installed, it s

5.2 Phone Line Polarity C.O. (Phone Company)C.O. (Phone Company)Phone InPhone InPhone OutPhone OutHomeHome86731542BypassSwitchDC PositiveDC Positive

5.3 Isolating Noise Problems If noise or hum is present on the resident’s phone line after installation of the 1812 telephone intercom system, use th

5.4 Troubleshooting Tables SYMPTOM POSSIBLE SOLUTION(S) Cannot get into programming mode. • Wrong master code entered. Start over. • Waiting too lo

SYMPTOM POSSIBLE SOLUTION(S) System generates tone when granting access to a visitor, but will not work on regular phone line. • Switch the wires on

5.5 Wire Diagram123456789101112131415161718MicVolMasterCode1234567891011SpeakerVolKeypad12345678ONMODEM / TCP ENBSW 1RedWhiteGreenYellowRedWhiteWhite+

5.6 Accessories Secondary Keypad Allows remote activation of the system relays by use of the access codes. Does not provide any voice communication

2.4 Devices 2.4.1 Simple Access Code Programming ...30 2.4.2

5.7 Tables Complete the information in the tables on the following pages to maintain a record of the information that has been programmed into the 181

Directory Codes / Dial-Out Phone NumbersDirectory Code Name Phone Number 24 25 26 27 28 29 30 31 32 33 34 35 36

Access Code Log Sheet Name Access Code Time Zone Schedule Number Relay Momentary or Hold

1812-161-E-1-10 Page 53

Important Notices FCC – United States This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Par

General Information • Prior to beginning the installation of the telephone entry system, we suggest that you become familiar with the instructions, i

Features • Unique telephone communication system allows homeowners to use their telephone as an intercom to speak to a guest at a front door or gate,

SECTION 1 - INSTALLATION Installation of the 1812 Plus Telephone Entry System involves the installation of the hardware and by-pass switch, and the w